2021 Telluride Detailing Thread

[Devo565]

Thanks everyone. It sounds like I need to invest in a decent pressure washer then, as a simple spray with the hose does nothing. I will look into having them ceramic coated as well maybe.

Are there any good entry level pressure washers for detailing that don’t cost a fortune. I already have a heavy duty gasoline pressure washer, but don’t want to have to fire that thing up every time I wash the car.

 

[Bigbadwolf]

Thanks everyone. It sounds like I need to invest in a decent pressure washer then, as a simple spray with the hose does nothing. I will look into having them ceramic coated as well maybe.

Are there any good entry level pressure washers for detailing that don’t cost a fortune. I already have a heavy duty gasoline pressure washer, but don’t want to have to fire that thing up every time I wash the car.

You can find a decent one at any hardware store or Amazon for 100 to 200. Just remember for detailing purpose higher gpm is more important than psi! Foam cannons work better with more gpm. Read reviews and look on you tube there's a guy that does home garage detailing setups and does some real world gpm test on some washers.

 

[Senator20]

I just use an electric Ryobi pressure from Home Depot. Spent a little over $100 on it. You will also use less water when cleaning your vehicles.

 

[gman1868]

Alright here’s a question for all you detailing nerds. My wife and I just built a home in a brand new development. Needless to say it’s become a full on construction zone as more and more houses go up. As a result, there Is mud, rocks, dirt, construction debris, mortar, and all kinds of other s**t in the street. But the mud and brown dust is the worst part.

I currently detail my cars about once a week, but no matter what I try I cannot keep the wheel wells clean for the life of me. The first time it rains all the dirt turns to mud and cakes up all around the tire. Is there a way to possibly ceramic coat the inner wheel well liners, to help this stuff fall off more easily with just a simple rinse?

We are expecting our new Telly any week now, and just the thought of having dirt all over the wheel wells is killing me. Nothing ruins the look of a newly detailed car more than having nice black tires and glossy paint but dirt all over the wheel liners. It’s so obvious and so ugly. Thanks in advance!!

For wheel well liners, there are a number of companies that make Ceramic coatings for trim. The trim made from of plastic polymers like the wheel well liners. There are ceramic products for plastic trim from companies such as Adams and GTechniq, I'm sure there are others. Once the plastic is coated with the ceramic product it will clean up very easily with a power washer and foaming cleaner.

Scott H of Correction Perfection has a 22 way test going:

______________________________

 

[gman1868]

For anyone looking for a power washer, your results will vary depending upon the machine you buy. For me, a gas powered washer was not an option so I looked for the best electric washer that wouldn't break the bank. The Adams Electric Pressure Washer 2.0 has 1.8GPM and 2000 PSI working flow and pressure which out performs the consumer models available at places like Home Depot and Lowes.

https://www.amazon.com/Adams-Pressu...ric+Pressure+Washer+2.0&qid=1614579484&sr=8-3

 

[naj2410]

For anyone looking for a power washer, your results will vary depending upon the machine you buy. For me, a gas powered washer was not an option so I looked for the best electric washer that wouldn't break the bank. The Adams Electric Pressure Washer 2.0 has 1.8GPM and 2000 PSI working flow and pressure which out performs the consumer models available at places like Home Depot and Lowes.

https://www.amazon.com/Adams-Pressure-Washer-Extension-Different/dp/B07TZ6PMBK/ref=sr_1_3?dchild=1&keywords=Adam's+Electric+Pressure+Washer+2.0&qid=1614579484&sr=8-3

this may sound like a dumb question so I apologize lol. but is a foam cannon compatible with all or most pressure washers? or do you need to buy a separate foam cannon gun?

 

[gimpy]

A month or so ago, I bought a new Tri Nova foam cannon. I have an old, about 15 year old, power washer (Husky-don't know where I got it, probably given to me a few years ago, never used until now). I filled the foam cannon with soap, but then found out I could not connect it to my power washer. I looked/asked around for a couple of weeks before I found the right connection on line. It cost me about $11.00.

I don't know if my power washer would not fit because it was too old, or if they are all that way (I think not because no one ever mentioned it in their videos I looked at). I will look for the link to the adapter I bought just in case you might need it and then edit this post with the link.

 

[Joep66]

this may sound like a dumb question so I apologize lol. but is a foam cannon compatible with all or most pressure washers? or do you need to buy a separate foam cannon gun?

I just bought a foam cannon and wand for my Sunjoe powerwasher. Just have to be careful of what size fittings are on the hose, or where ever you want to connect. I think most foam cannons are ok with 1700-2000 psi powerwasher, probably higher. Don't remember the exact number, but it should be noted in the description of the foam cannon if you are worried about pressure.

______________________________

 

[gimpy]

Amazon.com: Pressure Washer Gun Adapter with 1/4” Female Quick Connect Fitting Compatible Bosch (Not AQT) / Husky: Garden & Outdoor

Amazon.com: Pressure Washer Gun Adapter with 1/4” Female Quick Connect Fitting Compatible Bosch (Not AQT) / Husky: Garden & Outdoor

www.amazon.com

 

[gimpy]

As you can see, I don't know how to add to/edit posts.

My old power washer needs an adapter or coupling extension (shown in the picture at the top of the pipe). Those two wings go into the end of the spray gun, and then twist 1/4 of a turn. I don't know if newer power washers have that type of a connection.

 

[gman1868]

this may sound like a dumb question so I apologize lol. but is a foam cannon compatible with all or most pressure washers? or do you need to buy a separate foam cannon gun?

If the question is about whether or not the quick disconnect fitting will work, not all fittings are created equal. Not that it's a common problem, but I had to but a different adapter for mine. Even though the hose and the cannon we the same diameter fitting, I had to get a different male adapter for my Griots foam cannon to fit the handle on the Adams washer. The one that came with the cannon was a little too long. So, regardless of which combination of cannon and power washer, you'll have to test it to see if it works.

Other issues to consider, the soap you're using and the flow and pressure the washer is capable of. Some foam cannons won't make foam very well with a low flow, low pressure washer. Ideally it's best to have 2 GPM and 2000 PSI operating pressure to make the cannons all work well. Sadly, most of the consumer brands at the big box store claim 2000+ PSI, but the operating pressure is only 1200-1500 PSI. Same issue with GPM, they typically flow around 1-1.2 GPM operating pressure.

I needed electric to operate in my garage, so a gas powered washer with 3000-4000 PSI wasn't an option. If money was no object, Kranzle has the best electric washers, but it wasn't in my budget to spend $1200 or more. I found the Adams was the best compromise of p[rice and performance.

I tried the Adams foam cannon with their soap but got unsatisfactory results (the foam was very runny). I bought the Griots cannon and foaming soap and that worked well. I also put an extra large RV water filter https://www.amazon.com/gp/product/B07B2LPLBQ/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1 on the input to the washer to make sure there weren't any water quality issues affecting foam production.

The people I see doing demos on YouTube typically don't use the inexpensive power washers because they just don't provide a consistent foam with different cannons and soap products.

 

[Frankie Knuckles]

View attachment 15848View attachment 15849
weather has been horrible here since we bought it. Was still only 5 degrees this morning but I had to get it cleaned up!

Looks amazing

______________________________

 

[Frankie Knuckles]

Got the chance to wash our baby today. Used the new Ryobi undercarriage sprayer too. Rinse undercarriage and wheels, Carpro IronX on the wheels. Rinse, then foam, and wash wheels with my new Griots microfiber wheel wands. Rinsed the car then foamed. The foam goes on thick, but not too thick. It runs off very slowly and takes the dirt with it. Wash with microfiber mitt then power rinse the car. Blow dry, then use my new Griots PFM large drying towel. I also use separate edgeless microfiber towels on the door jams, etc. Turned out pretty good.

See pics...

Damnnnn that’s got to be the best color......just saying. Looks amazing.

 

[Bigbadwolf]

Looks amazing

Thanks the weather here has been tough to keep clean. Seams like a neverending battle every weekend

 

[Jpzy17]

I’m deciding on PPF brands and noticed SunTek launched a new PPF this week called reaction that has ceramic coated properties on the surface. I only found one YouTube video showing this film but startung around 13:30 he does a comparison of hydrophobic properties between the reaction and another PPF. Pretty interesting stuff. This new one is making my decision tougher. Reaction Paint Protection Film | SunTek

 

[gman1868]

Check out Scott H's test of ceramic spray coatings at the 6 month point in the test. A couple of my favorites are doing very well, the Griots 3-in-1 Ceramic Spray was and the Meguiars Hybrid Ceramic wax.

______________________________

 

[Jpzy17]

Check out Scott H's test of ceramic spray coatings at the 6 month point in the test. A couple of my favorites are doing very well, the Griots 3-in-1 Ceramic Spray was and the Meguiars Hybrid Ceramic wax.

I wish the 303 Graphene would have been out when he started this test. That’s what I ended up using. Still fantastic after 2 months.

 

[RyanATX]

Can anyone suggest a brush to clean the black plastic trim areas around the bottom of the Telluride? Looking for something not too harsh. Any suggestions for cleaning it would be appreciated, thanks !

 

[DarkMossJustin]

Anyone ever try this stuff for the dark exterior plastic trim pieces?

Cerakote - CERAKOTE TRIM COAT KIT

Shop Cerakote CERAKOTE TRIM COAT KIT R-0GTKIT1004. Find the coating that fits your application. Choose from a wide variety of coatings with specific attributes and specialties.

www.cerakote.com

I'm going to order some and try them out.

 

[superk1977]

Anyone ever try this stuff for the dark exterior plastic trim pieces?

Cerakote - CERAKOTE TRIM COAT KIT

Shop Cerakote CERAKOTE TRIM COAT KIT R-0GTKIT1004. Find the coating that fits your application. Choose from a wide variety of coatings with specific attributes and specialties.

www.cerakote.com

I'm going to order some and try them out.

This looks good. I will have to order also.