H/K Amp & Speaker Breakout Harness

[G-288068]

Any harness still available for H/K amp?
I’m interested in one

 

[Mr. I am him]

This is for the H/K amp outputs, so speaker level. It's called a "breakout" harness so you can directly tap it for signal or add aftermarket components AFTER the H/K amp while still having the option to utilize all the stock wiring.

Are you still making and selling the harness? Shoot me a message at elvinwhite02@gmail.com I’d like to get one.

 

[Ronsanut]

@HLXHLX I too am interested and wpoul dloove to buy one of your harnesses. Are they stil available ?

 

[kettemaster]

I would like to order one too.

______________________________

 

[Dtomczyk]

Like others here I am reluctant to cut/tap into the factory wiring for the audio system and since I could not find one commercially available yet, I went ahead and made my own breakout harness for the Harman Kardon amplifier in my SX. I plan to install a new amp/dsp in a few months and this was the first step in my process. Bottom line it permits installation of aftermarket audio components without cutting/tapping of factory wires while also maintaining full use of that same factory wiring for speakers (we've seen elsewhere the challenges of running new speaker wire out into the doors). Thus far it works flawlessly with all channels intact for this particular connector...the center channel and front tweeter channels are located on the 2nd amp connector (w/inputs, pwr, gnd, etc), but I do not plan to use those in my future setup (disabled and crossover, respectively).

View attachment 29880
View attachment 29881

Is there any chance you have anymore left? I cant seem to message you on here so email me dtomczyk366@gmail.com with payment and ill send it right over. Thanks!

 

[ghosted23]

This is for the H/K amp outputs, so speaker level. It's called a "breakout" harness so you can directly tap it for signal or add aftermarket components AFTER the H/K amp while still having the option to utilize all the stock wiring.

I would also be needing one if they are available?

 

[G-418041]

I would like to order one as well sir

 

[Stahlkamania]

I haven’t reported back but this Harness WORKED PERFECTLY. I tapped into the side speaker wires on the harness for my Rockwell 8” slim powered sub that sits in the storage area of the trunk. It absolutely completes the sound I was hoping to get from the overall system.

______________________________

 

[2low73]

Great work, I would like to purchase one as well. Thanks

 

[Cajun_25WOLFsxPxL]

@HLXHLX, I would like to purchase one of the breakout harnesses please. charles.palmer@gmail.com

 

[elbgsx9]

PM sent

Hi HLXHLX, just bout a used SX-Xline, are you still willing to sell the speaker harness?

 

[Rallens]

Hi @HLXHLX if you’re still making the breakout harness I would love one. Please email me with info on how to order one rallens169@yahoo.com. Thank you

______________________________

 

[JStone1973]

Has anyone received a harness lately? Just trying to find out if he is still making them. Thanks!

 

[Damion24]

Also looking for a breakout harness, I have a 2025 SX-Prestige X-Line Telluride. In houston TX. Looking to buy ASAP. @HLXHLX

 

[DOTdaddy]

@HLXHLX Hopefully You are still around in 2025 and making those harnesses! I have twin 21 Telluride SXPs aptly named Rumor & DejaVu. However Rumor wants some "junk in the trunk" so I need to give her some implants, and "COULD" build the harness if I had part numbers and knew where to source them, But Im a busy Dad, and would rather pay you for your entrepreneurial spirit. Pulley96@yahoo.com is the best way to connect. Thanks in advance my man! -Be good if you can't be bad-

 

[Littles_Gigi]

Like others here I am reluctant to cut/tap into the factory wiring for the audio system and since I could not find one commercially available yet, I went ahead and made my own breakout harness for the Harman Kardon amplifier in my SX. I plan to install a new amp/dsp in a few months and this was the first step in my process. Bottom line it permits installation of aftermarket audio components without cutting/tapping of factory wires while also maintaining full use of that same factory wiring for speakers (we've seen elsewhere the challenges of running new speaker wire out into the doors). Thus far it works flawlessly with all channels intact for this particular connector...the center channel and front tweeter channels are located on the 2nd amp connector (w/inputs, pwr, gnd, etc), but I do not plan to use those in my future setup (disabled and crossover, respectively).

View attachment 29880
View attachment 29881

Are you selling them? Or do you have the instructions for making one.

______________________________

 

[dansaleen_04]

Like others here I am reluctant to cut/tap into the factory wiring for the audio system and since I could not find one commercially available yet, I went ahead and made my own breakout harness for the Harman Kardon amplifier in my SX. I plan to install a new amp/dsp in a few months and this was the first step in my process. Bottom line it permits installation of aftermarket audio components without cutting/tapping of factory wires while also maintaining full use of that same factory wiring for speakers (we've seen elsewhere the challenges of running new speaker wire out into the doors). Thus far it works flawlessly with all channels intact for this particular connector...the center channel and front tweeter channels are located on the 2nd amp connector (w/inputs, pwr, gnd, etc), but I do not plan to use those in my future setup (disabled and crossover, respectively).

View attachment 29880
View attachment 29881

do you have any more harnesses for sale? I am interested for my 25 Telly.